Autoclave & Sterilizer Service
Dental autoclave repair and routine autoclave servicing: descaling, door seals and cycle diagnostics, including Midmark, Tuttnauer, SciCan and Pelton & Crane units. We also handle new autoclave and sterilizer setup and installation, from unboxing and plumbing to first cycle validation. We keep your sterilization compliance airtight without downtime you can't afford.
Need autoclave repair, scheduled servicing, or a new autoclave set up and installed? We come to offices and practices across Orange County — Irvine, Mission Viejo, Newport Beach, Santa Ana and every city in between — so a failed spore test, a leaking door seal, or a new unit waiting to be commissioned never puts your schedule on hold. We repair and service Midmark (M9, M11), Tuttnauer (EZ9, EZ10, T-Edge), SciCan STATIM and BRAVO, and Pelton & Crane autoclaves.
Brands We Service
Autoclave problems we fix
- Failed spore tests and sterilization failures
- Door seal and gasket leaks
- Not reaching or holding temperature or pressure
- Pump, solenoid valve and heater failures
- Water fill, drain and level sensor faults
- Error codes and aborted cycles
- Descaling and routine preventive servicing
Common questions
How much does dental autoclave repair cost?
Our autoclave repair pricing is competitive compared to other Orange County service providers. After an inspection we give you a clear quote up front, with no surprise charges.
How long does autoclave repair take?
We turn autoclave repairs around as quickly as possible. If the fix only needs cleaning, seals or in-stock parts it's often same-day; if a specific part has to be ordered, we'll tell you the timeline before we start.
Which autoclave brands do you repair?
We repair Midmark (including M9 and M11), Tuttnauer (including EZ9, EZ10 and T-Edge), SciCan (STATIM and BRAVO) and Pelton & Crane autoclaves, along with most other major dental autoclave and sterilizer brands.
Do you repair Tuttnauer and Midmark autoclaves?
Yes. Tuttnauer and Midmark are two of the units we service most, for repairs, routine servicing and new installs.
Can you set up and install a new autoclave or sterilizer?
Yes. We handle new autoclave and sterilizer installation end to end — plumbing, venting, calibration and first cycle validation — so it's compliant and ready to use from day one.
My autoclave won't heat up. What could be wrong?
The usual causes are a failed heating element, a faulty temperature sensor, a leaking door seal, a stuck valve, or scale buildup. If an empty cycle still won't reach temperature, stop using it for sterilization and call us for an inspection.
What should I do if my autoclave fails a spore test?
Take the unit out of service, check the indicator and how the load was packed, and re-test. If it fails again, the autoclave needs inspection, and we can diagnose and repair it on site.
How often should a dental autoclave be serviced?
Follow your manufacturer's maintenance schedule, and have it professionally inspected at least once a year. Regular descaling and seal checks prevent most failures.
Other equipment we service across Orange County.
Handpiece Repair
High-speed and slow-speed handpiece repair and rebuilds.
Chair Install, Disassembly & Repair
Dental chair installation, upholstery, hydraulics and motor repair.
Compressor & Vacuum Systems
Air compressor and vacuum pump repair, install and rebuilds.
X-Ray & Imaging System Install
Digital sensor, pano and CBCT imaging install and repair.
Microscope Install
Surgical and endodontic microscope installation and calibration.
Suction & Delivery Unit Repair
Delivery unit, suction line and vacuum pump troubleshooting.
Preventative Maintenance Plans
Scheduled equipment maintenance to catch problems before patients do.
Emergency Callout
Same-day and after-hours emergency dental equipment repair.
Obturation System Repair
System B and other endodontic obturation unit repair and service.
Custom Solutions on Request
One-off installs, retrofits and equipment moves.
Ready to get your autoclave & sterilizer service scheduled?
Call Mo Akhbari and describe the issue. We'll tell you what it likely is and get an inspection scheduled.